Our below ground one metre diameter packaged pumping station with single guide rail mounted pump is designed for the transfer of sewage and waste water from domestic and commercial properties where connection to the mains drain is not possible.
The guide rail system consists of a set of galvanised steel rails inside the tank which run between a pedestal base at the bottom of the tank and an upper guide rail bracket at the top of the tank.
The pump is fitted with a claw which allows the pump to slide up and down the guide rail, the weight of the pump forms the discharge connection when the pump is lowered on to the pedestal base.
The pump comes with a lifting chain, which means the pump can be quickly and easily removed for maintenance, completely eliminating the need to drain the tank and physically uncouple the connections.
Our pumping stations are formed of a premium quality polyethylene or GRP (>3.0m) tank and a submersible sewage pump, the depth of the tank needed will be dependent on the invert level and storage required.
All internal pipework including non-return valves comes pre-assembled and connected inside the tank. We also supply as standard two 110mm rubber grommets for the inlet pipes. A manhole cover is available as an optional extra.
Wet wipes and sanitary items block pumps and pipes, don’t flush them, bin them
We recommend that all pumping stations purchased from us are serviced regularly to ensure that all pumps, pipework, valves and control equipment are kept in full working order.
One metre width polyethylene tank (depths up to 2.5m) / GRP tank (depths 3.0m or above)
Choice of tank depth; 1.0m (860 litre capacity), 1.5m (1,175 litre capacity), 2.0m (1,550 litre capacity), 2.5m (1,950 litre capacity) and 3.0m (2,350 litre capacity)
Single guide rail system including pedestal base and pump claw
2 inch, 2½ inch or 3 inch discharge, supplied with internal pipework and finished with tank connector for connection to external discharge pipework
Non return valve and gate valve fitted into internal pipework
Mounted vortex pump with up to 80mm free solids passage
Submersible pump (230v) with up to 966 litre per minute flow rate and up to 9.7m lift (please note the pump can be upgraded to suit requirements, ask for details)
Automatic operation – included high level alarm
Supplied with two 110mm seal for inlet hole to be cut on site, additional inlet seals available on request
Pedestal, upper bracket, guide rails and claw for mounting pump
Internal Pipework
Rigid Pipework
Non-return Valves
1
Gate Valves
1
Float Switches
Attached to pump
Float Switch Bracket
Optional
High Level Alarm and Float Switch
Included
110mm Inlet Pipe Seals
2
Manhole Cover
Optional
Kiosk
Optional
MDPE Pipe
Optional
Compression Fitting
Optional
Product Description
Our below ground one metre diameter packaged pumping station with single guide rail mounted pump is designed for the transfer of sewage and waste water from domestic and commercial properties where connection to the mains drain is not possible.
The guide rail system consists of a set of galvanised steel rails inside the tank which run between a pedestal base at the bottom of the tank and an upper guide rail bracket at the top of the tank.
The pump is fitted with a claw which allows the pump to slide up and down the guide rail, the weight of the pump forms the discharge connection when the pump is lowered on to the pedestal base.
The pump comes with a lifting chain, which means the pump can be quickly and easily removed for maintenance, completely eliminating the need to drain the tank and physically uncouple the connections.
Our pumping stations are formed of a premium quality polyethylene or GRP (>3.0m) tank and a submersible sewage pump, the depth of the tank needed will be dependent on the invert level and storage required.
All internal pipework including non-return valves comes pre-assembled and connected inside the tank. We also supply as standard two 110mm rubber grommets for the inlet pipes. A manhole cover is available as an optional extra.
Wet wipes and sanitary items block pumps and pipes, don’t flush them, bin them
We recommend that all pumping stations purchased from us are serviced regularly to ensure that all pumps, pipework, valves and control equipment are kept in full working order.
1 Metre Diameter Pumping Station with Single Guide Rail
Product description
Our below ground one metre diameter packaged pumping station with single guide rail mounted pump is designed for the transfer of sewage and waste water from domestic and commercial properties where connection to the mains drain is not possible.
The guide rail system consists of a set of galvanised steel rails inside the tank which run between a pedestal base at the bottom of the tank and an upper guide rail bracket at the top of the tank.
The pump is fitted with a claw which allows the pump to slide up and down the guide rail, the weight of the pump forms the discharge connection when the pump is lowered on to the pedestal base.
The pump comes with a lifting chain, which means the pump can be quickly and easily removed for maintenance, completely eliminating the need to drain the tank and physically uncouple the connections.
Our pumping stations are formed of a premium quality polyethylene or GRP (>3.0m) tank and a submersible sewage pump, the depth of the tank needed will be dependent on the invert level and storage required.
All internal pipework including non-return valves comes pre-assembled and connected inside the tank. We also supply as standard two 110mm rubber grommets for the inlet pipes. A manhole cover is available as an optional extra.
Wet wipes and sanitary items block pumps and pipes, don’t flush them, bin them
We recommend that all pumping stations purchased from us are serviced regularly to ensure that all pumps, pipework, valves and control equipment are kept in full working order.
One metre width polyethylene tank (depths up to 2.5m) / GRP tank (depths 3.0m or above)
Choice of tank depth; 1.0m (860 litre capacity), 1.5m (1,175 litre capacity), 2.0m (1,550 litre capacity), 2.5m (1,950 litre capacity) and 3.0m (2,350 litre capacity)
Single guide rail system including pedestal base and pump claw
2 inch, 2½ inch or 3 inch discharge, supplied with internal pipework and finished with tank connector for connection to external discharge pipework
Non return valve and gate valve fitted into internal pipework
Mounted vortex pump with up to 80mm free solids passage
Submersible pump (230v) with up to 966 litre per minute flow rate and up to 9.7m lift (please note the pump can be upgraded to suit requirements, ask for details)
Automatic operation – included high level alarm
Supplied with two 110mm seal for inlet hole to be cut on site, additional inlet seals available on request
For more information on the full Poolstar pool, spa and wellness range or to speak to us about becoming a stockist please call 01284 658770 or email our sales team.
We are proud to be the official UK & Ireland Poolstar distribution partner.
Our below ground one metre diameter packaged pumping station with single guide rail mounted pump is designed for the transfer of sewage and waste water from domestic and commercial properties where connection to the mains drain is not possible.
The guide rail system consists of a set of galvanised steel rails inside the tank which run between a pedestal base at the bottom of the tank and an upper guide rail bracket at the top of the tank.
The pump is fitted with a claw which allows the pump to slide up and down the guide rail, the weight of the pump forms the discharge connection when the pump is lowered on to the pedestal base.
The pump comes with a lifting chain, which means the pump can be quickly and easily removed for maintenance, completely eliminating the need to drain the tank and physically uncouple the connections.
Our pumping stations are formed of a premium quality polyethylene or GRP (>3.0m) tank and a submersible sewage pump, the depth of the tank needed will be dependent on the invert level and storage required.
All internal pipework including non-return valves comes pre-assembled and connected inside the tank. We also supply as standard two 110mm rubber grommets for the inlet pipes. A manhole cover is available as an optional extra.
Wet wipes and sanitary items block pumps and pipes, don’t flush them, bin them
We recommend that all pumping stations purchased from us are serviced regularly to ensure that all pumps, pipework, valves and control equipment are kept in full working order.
One metre width polyethylene tank (depths up to 2.5m) / GRP tank (depths 3.0m or above)
Choice of tank depth; 1.0m (860 litre capacity), 1.5m (1,175 litre capacity), 2.0m (1,550 litre capacity), 2.5m (1,950 litre capacity) and 3.0m (2,350 litre capacity)
Single guide rail system including pedestal base and pump claw
2 inch, 2½ inch or 3 inch discharge, supplied with internal pipework and finished with tank connector for connection to external discharge pipework
Non return valve and gate valve fitted into internal pipework
Mounted vortex pump with up to 80mm free solids passage
Submersible pump (230v) with up to 966 litre per minute flow rate and up to 9.7m lift (please note the pump can be upgraded to suit requirements, ask for details)
Automatic operation – included high level alarm
Supplied with two 110mm seal for inlet hole to be cut on site, additional inlet seals available on request
Pedestal, upper bracket, guide rails and claw for mounting pump
Internal Pipework
Rigid Pipework
Non-return Valves
1
Gate Valves
1
Float Switches
Attached to pump
Float Switch Bracket
Optional
High Level Alarm and Float Switch
Included
110mm Inlet Pipe Seals
2
Manhole Cover
Optional
Kiosk
Optional
MDPE Pipe
Optional
Compression Fitting
Optional
Over 1,100 reasons why customers choose us
We have over 1,000 five star reviews on TrustPilot, below is some of our most recent customer feedback.
You can trust us when we say we care about the service we provide both before and after your purchase, there are hundreds more five star reviews from happy customers on our Trustpilot page.
