Not sure what size heat pump you need? Use our sizing guide or request a free quote
Key features
Compact plug and play heat pumps that are suitable for Summer season (June to August) heating of small above-ground pools
Up to 3.05kW (XXS3), 4kW (XXS4) and 5.6kW (XXS6) of heat output at air temperature of 26°C, water temperature of 26°C and target temperature of 27-28°C
Up to 2.51kW (XXS3), 3.1kW (XXS4) and 4.95kW (XXS6) of heat output at air temperature of 15°C, water temperature of 26°C and target temperature of 27-28°C
Ideal for Intex and Bestway above-ground pools that come supplied with filter pumps, maximum flow rate required 3.0m³/h (3,000 l/h)
Summer only (June to August), suitable for use when the air temperature is above 10°C (*please note unit will stop running if air temperature falls below 10 degrees)
Maximum input power 1.55kW, maximum input current 7.0A
Plug and play, comes with mains cable, RCD and UK plug, suitable for use in outdoor sockets
1 inch FBSP water connections, 1 inch to 32/38mm hose tails and clips included
R32 Refrigerant
Off white steel casing with black lid and base
Titanium heat exchanger, chlorine and salt resistant
Two year warranty, seven years on compressor and heat exchanger (parts only after first two years)
Downloads
Specifications (.pdf)
Manual (.pdf)
Specifications
Heating Capacity A26/W26 |
3.05 kW |
COP |
5.45 |
Heating Capacity A15/W26 |
2.51 kW |
COP |
4.53 |
Input Power (max.) |
0.95 kW |
Input Current |
4.4A |
Voltage |
230v |
Noise Level |
28dB(A) |
Refrigerant |
R32 |
Water Connections |
1 inch FBSP (32/38mm hose tails included) |
Nominal Flow |
1.5 m³/h (1,500 l/h) |
Dimensions (L x W x H) |
380mm x 280mm x 350mm |
Weight |
18Kg |
Heating Capacity A26/W26 |
4.0 kW |
COP |
5.45 |
Heating Capacity A15/W26 |
3.10 kW |
COP |
4.52 |
Input Power (max.) |
1.28 kW |
Input Current |
5.8A |
Voltage |
230v |
Noise Level |
29dB(A) |
Refrigerant |
R32 |
Water Connections |
Hose tails included |
Nominal Flow |
2.0 m³/h (2,000 l/h) |
Dimensions (L x W x H) |
380mm x 280mm x 350mm |
Weight |
20Kg |
Heating Capacity A26/W26 |
5.6 kW |
COP |
5.43 |
Heating Capacity A15/W26 |
4.95 kW |
COP |
4.54 |
Input Power (max.) |
1.55 kW |
Input Current |
7.0A |
Voltage |
230v |
Noise Level |
29dB(A) |
Refrigerant |
R32 |
Water Connections |
Hose tails included |
Nominal Flow |
3.0 m³/h (3,000 l/h) |
Dimensions (L x W x H) |
420mm x 360mm x 436mm |
Weight |
24Kg |
What is COP?
COP stands for Coefficient of Performance
COP is quoted as a number, such as 5.6
For each kW of energy input, 5.6 x kW would be output
The higher the output, the lower the running costs
Installation
If you are thinking of heating your pool you should cover the pool when not in use as 80% of heat loss occurs through surface evaporation, a separate solar or bubble cover is a worthwhile investment if you don’t have an existing cover.
With an above ground pool it is especially important to keep it covered as these pools are not well insulated against heat loss – additional insulation around the sides and bottom of an above-ground pool can help to retain valuable heat – in fact properly insulating your pool can extend your season or even reduce the size of heat pump required.
All models are fitted with a mains cable, RCD and plug as standard, making them suitable for outdoor sockets, this cable can be removed and the unit can be hardwired if required.
Water inlet and outlet connections are 1 inch FBSP, 1 inch to 32/38mm hose tails and clips included.
If the flow rate through your heat pump is too high it can take longer to heat your pool or you may struggle to achieve your desired temperature, our bypass kit for above ground pools optimises the flow rate to maximise the heat transfer to your pool water. A bypass kit also allows the circulation and filtering of pool water without heating and for winterising your heat pump.
Your ProTeam XXS swimming pool heat pump should always be installed outside, restrictions on air flow around a heat pump such as dense vegetation or solid surfaces such as sheds, fences or walls will lead to a drop in efficiency and heating ability, it especially important that cooled air can be properly dispersed away from the unit.
While the casing provides protection from the weather, the XXS is intended for Summer use only, the unit should be disconnected and stored in a shed or garage when not in use over the Winter.
The manufacturer literature may state that the heat pump should be positioned above the waterline, the assumption being that pools are in-ground, therefore the heat pump would sit at ground level.
If you have an above-ground pool please also position your heat pump at ground level (therefore below the waterline), there is no need to elevate the heat pump.